Capacity: 16.384 Mbps, dynamically configurable
in 2 Mbps channels
Available module slots: 2
Encryption support: Symmetric 3DES
Front panel test points: RSSI (receive signal strength
indication), GND
Craft port interface: VT100 emulation via RS232 (DB9
physical interface)
AUX RS232: Provides embedded 9600 bps RS232 link
between both ends for transport of alarm information
other craft port interfaces
Management interface: 10BaseT/100BaseTX supports
SNMP and Telnet access across multiple hops
Software upgrades: Via TFTP over Ethernet interface
XMODEM over craft port interface
Alarms: Major alarm (RF link down), normally open and
normally closed relay contacts

Transmitter

Output power: +20 dBm (100 milliwatts) maximum

Frequency band:
2.4 GHz models: 2.4 to 2.4835 GHz
5.8 GHz models: 5.725 to 5.850 GHz
Channel bandwidth: 17 MHz
Intermediate frequency: 280 MHz

Receiver

Receive level threshold (@10 -6 BER):
2.4 GHz models
-88 dBm @ 16 Mbps (8xT1/E1 or 16 Mbps Ethernet)
-92 dBm @ 8 Mbps (4xT1/E1 or 8 Mbps Ethernet)
-95 dBm @ 4 Mbps (2xT1/E1 or 4 Mbps Ethernet)
5.8 GHz models
-87 dBm @ 16 Mbps (8xT1/E1 or 16 Mbps Ethernet)
-90 dBm @ 8 Mbps (4xT1/E1 or 8 Mbps Ethernet)
-93 dBm @ 4 Mbps (2xT1/E1 or 4 Mbps Ethernet)
Maximum error-free receive level: -30 dBm
Nominal receive level: -55 dBm

Frequency band:
2.4 GHz models: 2.4 to 2.4835 GHz
5.8 GHz models: 5.725 to 5.850 GHz
Channel bandwidth: 17 MHz
Intermediate frequency: 140 MHz

Frequency Pairs

2.4 GHz models
Channel 1: 2.416 GHz / 2.456 GHz
Channel 2: 2.422 GHz / 2.462 GHz
Channel 3: 2.428 GHz / 2.468 GHz
5.8 GHz models
Channel 1: 5.744 GHz / 5.824 GHz
Channel 2: 5.747 GHz / 5.827 GHz
Channel 3: 5.751 GHz / 5.831 GHz
RF/IF Interface
Antenna connector: female type-N
Impedance: 50 ohms
Maximum coax length for split configuration:
600 feet (180 meters) of 1/2-inch coax or 350 feet
(100 meters) of RG-8

Interface Card Options

Quad T1 Card
Capacity: 4xT1 (ANSI T1.403)
Interface type: DSX-1
Connectors: RJ-48C
Line code: B8ZS (default), AMI
Framing: ESF (default), D4
Alarms: AIS, Red, Yellow, BPVs, LOS
Loopbacks: Local and remote line, local and remote link

Quad E1 Card
Capacity: 4xE1 (CCITT G.703)
Interface type: G.703, G.704, and G.823 compliant
Connectors: 120 Ω RJ-48C, 75 Ω BNCs supported with
optional breakout panel
Line code: HDB3 (default), AMI
Alarms: LOS, LCV, AIS, RMT, OOF, CRC
Loopbacks: Local and remote line, local and remote link

Quad Ethernet Switch Card
802.3u compliant
Four auto-sensing 10BaseT/100BaseTX ports
Auto MDI/MDIX support on all interfaces
Full and half-duplex operation
Layer 2 switching and MAC bridging
Maximum frame size 1536 bytes (passes 802.1Q packets)
Back-pressure flow control for half-duplex interfaces
Pause-frame flow control for full-duplex interfaces

Environment

Indoor operating temperature:-25° to 65° C (-13° to 149° F)
Outdoor operating temperature: -40° to 65° C (-40° to 149° F)
Relative Humidity: Up to 95%, non-condensing

Physical

Dimensions: 1.7" (4.4 cm) (1U) H, 17.2" (43.7 cm) W, 11.4”
(28.9 cm) D (IDU and integrated chassis), 16” (40.8 cm) H, 9”
(22.9 cm) W, 3.9” (9.8 cm) D (ODU)
Weight: 5 lbs. (2.3 kg) (IDU), 7 lbs. (3.2 kg) (ODU), 7 lbs.
(3.2 kg) (integrated)
AC Power: 21-60 VDC, either polarity referenced to ground
Power Dissipation: 25 Watts maximum