FCD-E1 E1 CSU/DSU Termination Equipment

Features

E1 or Fractional E1 access unit
Supports one or two data ports with selectable sync data rates: n x 56 or n x 64 kbps
Optional sub-E1 drop & insert port for PABX connectivity
Optional high performance built-in Ethernet bridge
The E1 main link can be supplied with the following options:
- Built-in LTU
- Fiber optic interface
Failure immune sub-E1 ensuring uninterrupted service (G.703 only)
Data interfaces: V.35, RS-530, V.36/RS-449 or X.21
SNMP agent
Inband remote management
Dial-in option for remote out-of-band management
Dial-out for alarm report
E1 interface complies with: ITU G.703, G.704, G.706, G.732, G.823
Enhanced diagnostics include:
- User activated local and remote loopbacks
- Integrated BER tester
- Fractional E1 inband loop
Stores 24 hours of E1 network performance monitoring and last 100 alarms
Relay activation upon alarm event
Alarm mask configurable for any alarm

Description

FCD - E1 is an access unit for E1 or Fractional E1 services. It can be used as a rate and interface converter or as an integrating multiplexer for E1 and Fractional E1 services (see Figure 2).

FCD - E1 also operates opposite RAD's modular DXC (multiservice access node) products or other vendors' E1 equipment, for multilink star applications, such as access to SDH networks. The DXCs and FCD - E1 operate together with centralized SNMP network management (see Figure 3).

FCD - E1 can be ordered with a regular E1 (G.703) or a fiber optic link. Both configurations are also available with an optional sub-E1 drop & insert port. The unit can be ordered with either one or two data ports. The second port can be an Ethernet bridge port.

BASIC UNIT

The E1 interface is compatible with virtually all carrier-provided E1 services and meets ITU recommendations G.703, G.704, G.706 and G.732. It supports either 2 or 16 frames per multiframe, with or without CRC-4. Zero suppression over the line is HDB3. The integral LTU (optional) ensures a range of up to 2 km.

FCD - E1 can be ordered with a fiber optic link, which eliminates the need for an external fiber optic modem. The fiber optic link provides a secure link in hazardous or hostile environments. It complies with ITU standards G.921 and G.956.

1300 nm laser diode for use over single mode fiber at distances up to 62 km (38 miles)

1550 nm laser diode for use over single mode fiber for extended range up to 100 km (62 miles).

Timeslot assignment is programmable, allowing data from each data port and from the sub-E1 port to be placed into timeslots consecutively. FCD - E1 also provides additional flexibility, by giving full user control over the data ports timeslot allocation without restrictions.

Multiple clock source selection ensures maximum flexibility for supporting different applications. The E1 main link may be clocked from the recovered receive clock, from an internal oscillator, from one of the data ports or from the sub-E1 port.

Immunity to hardware and power failure is provided by bypassing the sub-E1 port to the main link (non fiber optic), ensuring uninterrupted service to the sub-E1 port.

FCD - E1 is available as a standalone unit. A rack mount adapter kit enables installation of one or two standalone units, side by side in a 19" rack.

USER INTERFACE

The following data port interfaces can be ordered: V.35, RS-530, V.36/RS-449 or X.21. The ports can operate in the following clock modes:

DCE transmit and receive clocks are output

DTE1 external transmit clock is input (coming from the user DTE)

DTE2 both the transmit and receive clocks are externally input

The optional built-in Ethernet bridge is a high performance remote, self-learning bridge. It is ideal as a LAN extender or segmenter over E1 link applications. The LAN table stores up to 10,000 addresses and is automatically updated. Filtering and forwarding is performed at the maximum theoretical rate of 15,000 pps (wire speed) and the buffer can hold 256 frames with a throughput latency of 1 frame. Filtering can be disabled for extender or segmenter applications. The Ethernet port is available with either 10BaseT (UTP) or 10Base2 (BNC) interface. The Ethernet port with 10BaseT operates in full duplex mode, while the one with 10Base2 operates in half duplex.

The optional sub-E1 port can be configured to work without CRC-4, while the E1 main link is working with CRC-4. This enables connection of E1 equipment not supporting CRC-4, over an E1 network that is working with CRC-4.

MANAGEMENT & MAINTENANCE

Setup, control and monitoring of status and diagnostics information can be activated via:

FCD - E1 has an internal SNMP agent and can be controlled by any generic SNMP station or by the RADview SNMP network management application.

FCD - E1 supports dial-in, dial-out modem connections. These connections can be used for remote out-of-band configuration, monitoring and for sending callout alarm messages using the ASCII (terminal) or SLIP protocols.

Inband management can be performed by using the spare bits (Sa bits) on timeslot 0 or through a dedicated timeslot that supports proprietary protocol and Frame Relay RFC 1490. This allows setup, monitoring and diagnostics of the remote unit. Inband access by using spare bits on timeslot 0 is possible only if those bits are passed transparently end-to-end.

Maintenance capabilities include user activated local and remote loopbacks at the E1 main link, sub-E1 and data ports. The user can activate a BER test for each data or sub-E1 port individually. Each data or sub-E1 port responds to an ANSI FT1 RDL (T1E1.2/93-003) inband loop code, generated from the remote FCD - E1 or DXC in a specific bundle of timeslots allocated only to that port.

When operating with CRC-4, E1 network statistics are stored in memory according to RFC-1406. The statistic information may be retrieved locally through the control port.

Toll Free