VoIP Channel
Bank
------------
P32mxi

Specifications

General P32mxi System Capabilities

• Dual T1/E1 Network Interfaces

• Up to 32 total Analog (VF) Interfaces

• Long Loop (18,000 ft./1900 ohm) FXS Interfaces

• T1/E1 Conversion (with A to Mu-law Conversion)

• DID (DPT/DPO) Support Integrated CSU (T1)

• Autosensing 10/100 Base-T Ethernet

• Integrated Battery Charger

• Signaling Conversion: FX to E&M, FX to FX, E&M to R2 Digital

• Graphical User Interface (Local and Remote)

• SNMPv2 Management

• Supports Caller ID / CLASS Features

• True Sine Wave Ringing Generator

Intelligent Call Routing Features

• Inbound/Outbound Call Routing

• Station-to-Station Calling

• Call Forwarding

• Remote Table Programming

• Digit Deletion/Digit Insertion

• Call Blocking

• "Ringdown" Circuit Using Switched Networks

• DNIS and DID RoutingDigit Translation

• Call Transfer

• Local Number Portability

• Support Route Diversity/Redundancy

• 911 Override

• Inbound/Outbound Call Statistics

Advanced Channel Bank Features

• Timer-based Answer/Disconnect Supervision

• Voice Activity Detection Answer/Disconnect

• Supervision Selectable Tones and Cadence (150 countries)

• TR-08 Remote Terminal Emulation

NETWORK INTERFACE MODULES (2 per chassis)

• T1 (D4, ESF and TR-08) interface supports FX and E&M Wink/Immediate signaling

• E1 interface (75 and 120 ohm) supports E&M Wink/Immediate and R2 Digital Signaling

• Future SDSL/HDSL2/G.SHDSL interface

• Quad FXS/DPO Long Loop interface (18,000 ft. CSA); FCC approved for outside plant or interoffice use

• Quad FXS/DPO Short Loop interface (3,000 ft.)

• Quad FXO/DPT interfaces

T1: ANSI T1.403/AT&T 54016, 62411 & 43801

E1: G.703, G.704, G.731, G.732, G.775, G.962, O.162, Q.421, Q.422, TBR 012 and TBR 013

• Configured by the StarCAD 9000 GUI (Windows only)

• SNMPv2 Management via SLIP (craft port), Network Interface (via Frame Relay or ATM), or Ethernet

RFC 1155/11571213/1901 (SNMP core); RFC 1493 (Bridge); RFC 1471/ 1472/1473/1474 (PPP); ILMI; RFC 2515 (ATM); LANE; RFC 2665; RFC 2863 (IF); RFC 1406 (T1/E1); Custom System MIB

Internal or Loop timing from either network module

• AC or DC with integrated battery charger and battery

testing

• AC 95-135 VAC, 50/60 Hz

• DC input -42 to -60 VDC

• Maximum Power 90W

• Remote battery test function

• Automatic "Float" & "Equalize" for longer battery life

• Remote monitoring of internal temperature and power supply voltages

• True sine wave ringing generator

• NRTL Safety Listed: Certified to UL 1950, Certified to CAN/CSA C22.2 Std

• FCC Part 15 class A Radiated Emissions Control

• FCC Part 68, CS-03 Listed for connection to PSTN

• Operating Temperature 0o to 50 o C (32 o to 122 o F)

• Relative Humidity 0 to 95%

• 7.7" L x 13" W x 1.75" H

• 5.4 pounds fully configured