| |
This product has been discontinued and
available in a newer model at our
netperformer website
ACT
Networks� SDM-9400 multi-service integrated
access device is a packetized voice and data
solution, and the workhorse of the NetPerformer
family � a suite of products that has been
optimized for the needs of complex, distributed
enterprise networks. Typically these networks
include a wide variety of data and telephony
requirements, with various sites needing
differing amounts of functionality, density and
performance.
The SDM-9400 is designed for the regional
office, where voice and data traffic is
aggregated and redistributed to remote sites. By
packetizing and compressing voice traffic, then
delivering it with data over a Frame Relay or IP
network, the SDM-9400 allows companies to save
money on their monthly telephony service. PVC
bundling and switching also saves money on
monthly service fees, by eliminating the need
for a fully meshed PVC architecture.
The SDM-9400 unit can support up to eight analog
or thirty digital voice channels. The analog
ports can be configured for E&M (Types I, II
and V), FXS or FXO support. The digital channels
are connected via PBX through T1 or E1 ports.
Ethernet or Token Ring LAN support can also be
added, as well as fractional T1 or E1 WAN
connections.
All voice and data entering the unit is
prioritized by protocol then combined for
transport over a single Frame Relay connection
via private or public networks. This
functionality is provided by PowerCell � ACT
Networks� award-winning, cell-based
prioritization technology.
|
|
FEATURES & BENEFITS |
Integrated
voice and data � in
an extensible package, makes the SDM-9400 an ideal
solution for the needs of the regional office in a
converged network. The SDM-9400, in conjunction with the
rest of the NetPerformer
product line, allows each individual site to be
configured with just the right combination of services,
performance and scalability, avoiding unnecessary cost.
Support for modem and fax � means the SDM-9400
can support all the telephony needs of today�s
distributed networks, savings cost by integrating all
types of traffic onto a single network.
Digital voice support � with 30-channel
capacity, along with support for key signaling
methodologies, let the SDM-9400 connect to the world�s
most popular PBX units.
Any-to-any voice switching � integrates the
disparate phone systems of individual sites. This
eliminates the need for consistency among sites, saving
cost and increasing flexibility.
The SDM-9400 supports PowerCell � ACT�s
award-winning technology for voice and data integration
and prioritization. This allows the entire network to
operate at optimal performance for all supported traffic
types.
SNMP-compliant MIBs and graphical management �
through ACTview 2000, including integration with Hewlett
Packard�s OpenView for Windows95/NT, let the SDM-9400
be managed using today�s most popular and universal
network management paradigms.
Adherence to standards � lets the SDM-9400
seamlessly integrate with any public network, and
ensures compatibility with leading Frame Relay switches.
|
SPECIFICATIONS |
| System
Details: |
- Desktop
or rackmount chassis, 8 serial ports and 10
expansion slots
- Serial
connectors: DB-25 female
- Serial
interfaces: RS-232C, X.21/V.11, V.35/V.11, RS-530,
RS-449/RS-422 (software configurable)
- Power:
90 to 264 VAC 50/60 Hz or �48 VDC
- Optional
redundant AC power
- Network
topology: Public and private frame relay, mesh,
hierarchical, star and point-to-point
|
Expansion Options: |
- Number
of expansion slots: eight 16-bit slots, four 32-bit
slots (two shared for a total of 10 simultaneous
slots)
- Voice
modules:
- VFC-03:
1-port analog telephony
- DVC-06:
6-port digital telephony channel processor
module
- T1C:
1-port T1 PBX interface
- E1C75:
1-port E1 PBX interface (75 ohm)
- E1C75-1M:
1-port QSIG E1 PBX interface (75 ohm)
- E1C120:
1-port E1 PBX interface (120 ohm)
- E1C120-1M:
1-port QSIG E1 PBX interface (120 ohm)
- ISDN-03:
ISDN BRI Digital PBX Interface
- ISDN
CEM: ISDN BRI
- LAN
interfaces (32-bit modules):
- MOD-ETH-02:
10BaseT (RJ45) or 10Base2 (BNC)
- MOD-TR-02:
STP (DB-9) or UTP (RJ45)
- Network
interfaces (32-bit modules):
- T1-G703-P2-02:
T1 DSU/CSU
- T1-G703-75P2-02:
E1 DSU/CSU (75 ohm)
- T1-G703-120-P2-02:
E1 DSU/CSU (120 ohm)
- Dual
port model
- Up
to 32 logical ports
- Drop
and insert, RJ48 connectors for T1 and E1 120
ohms
- BNC
connectors or E1 75 ohms
|
Network Connections: |
- Number
of trunks: up to 8
- Circuits:
leased, switched or frame relay
- Link
port protocols:
- Synchronous
full duplex HDLC, frame relay RFC-1490
- User-UNI,
Network-UNI, PowerCell
- Rates:
1.2Kbps to 2.048Mbps
- Link
port speed: 1.2Kbps to 2.048Mbps
- Frame
relay:
- Local
management interfaces: LMI, ANSI T1.617 / Annex
D, ITU-T Q.933 / Annex A, CLLM or disabled
- PVCs:
96 per node
- Automatic
node discovery and rerouting with least cost metric
routing
- Automatic
load balancing, bandwidth on demand (over leased
line) and dial back-up, time-of-day connect
- Dialing
Protocols: V.25bis, X.21, AT and control leads
|
Telephony Features: |
- Voice
compression algorithms: ACELP 8Kbps, 5.8Kbps,
4.8Kbps, ACELP Comfort Noise 8Kbps, 6Kbps, ADPCM
G.726 (analog only), PCM G.711
- Digital
telephony channels: up to 30
- T1:
B8ZS/B7ZS/AMI line coding, Mu-law coding, D4/ESF
framing, robbed bit signaling, 100-ohm impedance
- E1C
signaling: CAS, R2, transparent channel 16
- E1C-1MB
signaling: QSIG
- Analog
telephony channels: up to 8
- Analog
voice: up to 8 voice/fax channels (VFC-03
modules)
- Analog
interfaces: FXO, FXS, E&M 4w/2w, AC-15,
software configurable
- Impedance:
600/900 ohms or complex
- ISDN
BRI digital voice/fax channels: up to 18
- 3
BRI (6 telephony) per ISDN-03, Euro ISDN
signaling, NT or TE clocking (clock extraction
module required in some NT applications)
- Dialing:
DTMF, MF, pulse dial
- Fax
support: Group III at 2.4, 4.8, 7.2, 9.6, 12 and
14.4Kbps
- Modem
relay: V.32bis modulation up to 14.4Kbps
|
LAN Support: |
- Ethernet
interface (MOD-ETH-02): Ethernet II and IEEE 802.2,
802.3, SNAP
- Token
Ring interface (MOD-TR-02): IEEE 802.5, 4/16Mbps
- Protocol
support:
- IP
RIP v2 or Static, BootP/DHCP relay, OSPF, IPX
RIP and SAP, Source Routing, Source Routing
Transparent
- 802.1D
Spanning Tree Protocol (STP), MAC Layer,
Transparent Bridging
- Filter
Criteria: Based on protocol, address (source,
destination or SAP) or custom filtering
- 8
classes of service, 16 priority weights
|
Data Features (Non-LAN): |
- Number
of user ports: up to 8
- Maximum
speed: 2.048Mbps
- Data
compression: 4:1 (up to 256Kbps input)
- User
port protocols:
- SNA:
SDLC, LLC2 or frame relay RFC1490 (BAN, BNN),
maximum of 64 PUs per data module (types 1, 2.0,
2.1, 4/5), local SDLC and LLC2 spoofing, SDLC/LLC2
conversion
- Legacy
Sync: BDLC, HDLC, SDLC, X.25, X.25 over Frame
Relay (annex F/G), COP, BSC, DDCMP, VIP, ALC,
IBM/RJE, Uniscope, Poll/Select, Siemens Nixdorf,
JCA, Zengin
- Frame
Relay: RFC-1490, UNI-DTE, UNI-DCE
Asynchronous: ENQ/ACK, XON/XOFF, transparent,
CTS/DTR
- 8
classes of service, 16 priority weights
|
Physical Characteristics: |
- Height:
5.3� (13.3 cm)
- Width:
17� (43.2 cm)
- Depth:
18� (45.7 cm)
- Weight:
24 lbs. (10.9 kg)
- Shipping
weight: 34 lbs. (15.4 kg)
|
Environmental Tolerance: |
- Operating
Temperature: 0� � 45� Celsius
- Relative
Humidity: 10% � 90%, non-condensing
|
Emissions
and Immunity: |
- EN
55022: 1995
- EN
50082-1: 1992
- EN
60555-2 / -3 : 1987
- AS/NZS
3548
- CE
Mark: EC Directive 89/336/EEC, 'Electromagnetic
Compatibility Directive'
|
Safety Compliance: |
- UL
1950
- CSA
C22.2 No. 950
- ACA TS
001 - 1996
- EN
60950 : 1992 / A1 : 1993 / A2 : 1993 / A3 : 1995
- CE
Mark: EC Directive 73/23/EEC, 'Low Voltage
Directive'
|
Network
Compliance: |
- I-CTR
2
- TS 002
- TS 003
- FCC
Part 68
- IC
CS03
- CE
Mark: EC Directive 98/13/EEC, �Telecommunications
Terminal Equipment Directive�
|
CE Marking: |
- EC
Directive 93/465/EEC, 'CE Marking Directive'
|
Network Management: |
- SNMP
management via ACTview 2000 Network Management
System for HP OpenView
- Menu
driven async console port (VT-100) via DB9 male
connector, autosensing DTE/DCE
- Remote
Telnet access to command port
FTP upload and download of software and
configuration
- Traps,
traces and extended statistics
- Username/password
security control administrative filtering
|
|
|
